Brand: Henning
Part number: 1008382
Scope of delivery:1 pc Top-hat rail length 14 cm, standard mounting rail 35 mm x 7.5 mm3 pcs. Pan head tapping screws with Phillips 3.9 x 9.5, DIN 79816 pcs. Standard lamp terminals (WAGO lamp connection terminal for connecting solid, single-wire conductors and ferrules with flexible, multi-wire con..
Brand: Henning
Part number: 1008381
With the Henning LIGHTwatcher you can reduce your electricity costs.Event-controlled light switch-off when stationary, minimizing the need for a standstill according to VDI 4707Easy installation directly into the lighting circuitAutonomous detection of car and door movements (patent pending)no inter..
Brand: Henning
Part number: 1008041
The donut sensors of the RC-light series are able to measure weights of all types of rope, belt or other support mean. The sensor will have to be calibrated by putting weights into the car.The sensors are easy to operate and need only to be connected to an evaluation unit AE16 or AE8 without e..
Brand: Henning
Part number: 1008042
The new rope load sensor LS-light suits shaft heads of little height and narrow-layed ropes thanks to its compact size.The range of applicable rope diameters from 4 to 13 mm also accords with the requirements.Up to 16 sensors can be connected by their 2,5-m-cables to the new evaluation unit AE16 lig..
Brand: Henning
Part number: 1008043
Only a few minutes are needed to install the MultiRope sensors:The installation only requires the screws of the retaining strap to be loosened and the sensor to be put against the rope. The retaining strap is then closed again and the screws are tightened up until the rope is pressed against the sen..
Brand: Henning
Part number: 1008044
Only a few minutes are needed to install the MultiRope sensors:The installation only requires the screws of the retaining strap to be loosened and the sensor to be put against the rope. The retaining strap is then closed again and the screws are tightened up until the rope is pressed against the sen..
Brand: Henning
Part number: 1008031
12 independent measuring channels, 3 alarm relays for freely programmable loads, an additional alarm relay for slack rope detection and load distribution monitoring. Programming via LED display and 3 buttons or via the USB interface and the free WeightWatcher softwareThe features at a glance:Max. 12..
Brand: Henning
Part number: 1008032
12 independent measurement channels Programming via LED display and 3 buttons, via the USB interface and the free WeightWatcher software or via the CANopen interface (e.g. with the CanWizard)The features at a glance:Max. 12 load sensorsNew measuring principle increases measuring accuracy without cal..
Brand: Henning
Part number: 1008033
The RC-series of “Donut”- sensors are able be measure absolute weights at each rope or belt, thereby making calibration with weights redundant. Plug ‚n Play - The sensors are ready for immediate use after connection with an evaluation unit AE12 without the time consuming entering of calibration para..
Brand: Henning
Part number: 1008034
The RC-series of “Donut”- sensors are able be measure absolute weights at each rope or belt, thereby making calibration with weights redundant. Plug ‚n Play - The sensors are ready for immediate use after connection with an evaluation unit AE12 without the time consuming entering of calibration para..
Brand: Henning
Part number: 1008035
The Henning over-load measuring system embodies a new measuring principle: At each rope, an individual load sensor is mounted which no longer has to be calibrated at the lift using weights. The measurement signals are sampled in a controller unit, permitting a check of both the cab weight and even r..
Brand: Henning
Part number: 1008036
The Henning over-load measuring system embodies a new measuring principle: At each rope, an individual load sensor is mounted which no longer has to be calibrated at the lift using weights. The measurement signals are sampled in a controller unit, permitting a check of both the cab weight and even r..
Brand: Henning
Part number: 1008037
The AElight 16 model series now replaces the previous AE16 overload evaluation unit and also has a new, completely revised design...
Brand: Henning
Part number: 1008038
The AElight 8 model series now replaces the previous AE8 overload evaluation unit and also has a new, completely revised design...
Brand: Henning
Part number: 1008039
In the development of the WeightWatcher Beam, the latest product of the WeightWatcher light series, our development department was able to incorporate the know-how acquired over many years. Special emphasis was placed on ease of installation and the desire of many customers for an inexpensive, yet h..
Brand: Henning
Part number: 1008040
The donut sensors of the RC-light series are able to measure weights of all types of rope, belt or other support mean. The sensor will have to be calibrated by putting weights into the car.The sensors are easy to operate and need only to be connected to an evaluation unit AE16 or AE8 without e..
Showing 1 to 16 of 16 (1 Pages)